Enhancing the flame retardancy of polylactic acid nonwoven fabric through solvent-free transparent coating.

Polylactic acid (PLA) nonwovens, recognized as eco-friendly substitutes for petroleum-based synthetic fibers, face a significant challenge due to their inherent flammability. This work addresses this concern by synthesizing a hyperbranched polyphosphoramide flame retardant (TPDT) through a one-step polycondensation process without using solvent and catalyst. TPDT is subsequently applied to PLA nonwovens using a dip-pad finishing technique. Notably, with a mere 7 wt% weight gain of TPDT, the PLA nonwovens exhibit a substantial increase in the limited oxygen index (LOI) value, reaching 32.3 %. Furthermore, the damaged area in the vertical burning test is reduced by approximately 69.2 %. In the cone calorimeter test, 17 wt% weight gain of TPDT results in a 51.4 % decrease in peak heat release rate and a 56.0 % reduction in total heat release compared to the control PLA. Additionally, char residue increases from 1.5 wt% to 31.1 wt% after combustion. The strong affinity between TPDT and PLA molecules persists even after repeated abrasion, ensuring sustained flame retardancy. Importantly, the introduction of TPDT also imparts increased softness to the PLA nonwovens. This work addresses this concern by synthesizing a hyperbranched polyphosphoramide flame retardant (TPDT) through a solvent-free, catalyst-free, and one-step polycondensation process.

A Fluorination Strategy and Low-Acidity Anchoring Group in Self-Assembled Molecules for Efficient and Stable Inverted Perovskite Solar Cells.

Herein, we synthesized two donor-acceptor (D-A) type small organic molecules with self-assembly properties, namely MPA-BT-BA and MPA-2FBT-BA, both containing a low acidity anchoring group, benzoic acid. After systematically investigation, it is found that, with the fluorination, the MPA-2FBT-BA demonstrates a lower highest occupied molecular orbital (HOMO) energy level, higher hole mobility, higher hydrophobicity and stronger interaction with the perovskite layer than that of MPA-BT-BA. As a result, the device based-on MPA-2FBT-BA displays a better crystallization and morphology of perovskite layer with larger grain size and less non-radiative recombination. Consequently, the device using MPA-2FBT-BA as hole transport material achieved the power conversion efficiency (PCE) of 20.32% and remarkable stability. After being kept in an N2 glove box for 116 days, the unsealed PSCs' device retained 93% of its initial PCE. Even exposed to air with a relative humidity range of 30±5% for 43 days, its PCE remained above 91% of its initial condition. This study highlights the vital importance of the fluorination strategy combined with a low acidity anchoring group in SAMs, offering a pathway to achieve efficient and stable PSCs.

In Situ Growth Strategy to Construct "Four-In-One" Separators with Functionalized Polyphosphazene Coatings for Safe and Stable Lithium-Sulfur Batteries.

Lithium-sulfur batteries (LSBs) are facing many challenges, such as the inadequate conductivity of sulfur, the shuttle effect caused by lithium polysulfide (LiPSs), lithium dendrites, and the flammability, which have hindered their commercial applications. Herein, a "four-in-one" functionalized coating is fabricated on the surface of polypropylene (PP) separator by using a novel flame-retardant namely InC-HCTB to meet these challenges. InC-HCTB is obtained by cultivating polyphosphazene on the surface of carbon nanotubes with an in situ growth strategy. First, this unique architecture fosters an enhanced conductive network, bolstering the bidirectional enhancement of both ionic and electronic conductivities. Furthermore, InC-HCTB effectively inhibits the shuttle effect of LiPSs. LSBs exhibit a remarkable capacity of 1170.7 mA h g-1 at 0.2 C, and the capacity degradation is a mere 0.0436% over 800 cycles at 1 C. Third, InC-HCTB coating serves as an ion migration network, hindering the growth of lithium dendrites. More importantly, InC-HCTB exhibits notable flame retardancy. The radical trapping action in the gas phase and the protective effect of the shielded char layer in the condensed phase are simulated and verified. This facile in situ growth strategy constructs a "four-in-one" functional separator coating, rendering InC-HCTB a promising additive for the large-scale production of safe and stable LSBs.

The involvement of interferon regulatory factor 8 in regulating the proliferation of haemocytes in oyster Crassostrea gigas.

Interferon regulatory factor 8 (IRF8) is an important transcriptional regulatory factor involving in multiple biological process, such as the antiviral immune response, immune cell proliferation and differentiation. In the present study, the involvement of a previously identified IRF8 homologue (CgIRF8) in regulating haemocyte proliferation of oyster were further investigated. CgIRF8 mRNA transcripts were detectable in all the stages of C. gigas larvae with the highest level in D-veliger (1.76-fold of that in zygote, p < 0.05). Its mRNA transcripts were also detected in all the three haemocyte subpopulations of adult oysters with the highest expression in granulocytes (2.79-fold of that in agranulocytes, p < 0.01). After LPS stimulation, the mRNA transcripts of CgIRF8 in haemocytes significantly increased at 12 h and 48 h, which were 2.04-fold and 1.65-fold (p < 0.05) of that in control group, respectively. Meanwhile, the abundance of CgIRF8 protein in the haemocytes increased significantly at 12 h after LPS stimulation (1.71-fold of that in seawater, p < 0.05). The immunofluorescence assay and Western blot showed that LPS stimulation induced an obvious nucleus translocation of CgIRF8 protein in haemocytes. After the expression of CgIRF8 was inhibited by the injection of CgIRF8 siRNA, the percentage of EdU positive haemocytes, the proportion of granulocytes, and the mRNA expression levels of CgGATA and CgSCL all declined significantly at 12 h after LPS stimulation, which was 0.64-fold (p < 0.05), 0.7-fold (p < 0.05), 0.31-fold and 0.54-fold (p < 0.001) of that in the NC group, respectively. While the expression level of cell proliferation-related protein CgCDK2, CgCDC6, CgCDC45 and CgPCNA were significantly increased (1.99-fold, and 2.41-fold, 3.76-fold and 4.79-fold compared to that in the NC group respectively, p < 0.001). Dual luciferase reporter assay demonstrated that CgIRF8 was able to activate the CgGATA promoter in HEK293T cells after transfection of CgGATA and CgIRF8. These results collectively indicated that CgIRF8 promoted haemocyte proliferation by regulating the expression of CgGATA and other related genes in the immune response of oyster.

Study on the Wettability Alteration of Tight Sandstone by Low-Frequency Vibration and Nanofluid.

The efficiency of reservoir imbibition in continental tight sandstone reservoirs is severely hindered due to their intricate wettability characteristics. To address this challenge, we propose a novel synergistic approach that combines low-frequency vibration and nanofluid treatment. This method integrates physical shear and chemical wettability alteration to effectively modify the wettability of neutral oil-wet tight sandstone, thereby enhancing the imbibition process. In this study, we formulated a TX-100 nanofluid system through physical modification. By utilizing the contact angle as a benchmark for evaluation, we investigated the impact of low-frequency fluctuations on the wettability of oil-wet sandstone. Subsequently, we identified the optimal combination of wave parameters. Through isothermal adsorption experiments and mechanical analyses of oil droplets subjected to fluctuations, we systematically elucidated the mechanism by which fluctuations collaborate with nanofluids to alter the wettability of oil-wet sandstone. Furthermore, we evaluated the oil displacement efficiency of cores subjected to the combined action of low-frequency fluctuations and nanofluid treatment. Our findings revealed that the TX-100 nanofluid reduced the static contact angle of oil-wet sandstone by 58%. When assisted by the optimal fluctuation parameters, the nanofluid treatment contributed to a 64% reduction in the contact angle of strongly oil-wet sandstone. This effect further amplified the reversal of wettability in oil-wet sandstone. Through the application of various wave-assisted treatment agents, the efficiency of oil removal was increased by a minimum of 16%. Moreover, the recovery degree of wave-assisted nanofluid imbibition experienced a remarkable enhancement of 30.39%. Nuclear magnetic resonance analysis demonstrated a significant improvement in pore sizes smaller than 1 µm as a result of the composite process.

Surface modification of zinc oxide and its application in polypropylene with excellent fire performance and ultra-violet resistance.

Despite the advantages of easy moulding and excellent mechanical properties, there are still some shortcomings with polypropylene (PP) such as high flammability and poor ultra-violet (UV) resistance. In this work, modified zinc oxide (mZnO) was prepared by reacting zinc oxide nanoparticles (ZnO) with polysiloxanes, and the effect of mZnO on the effectiveness of intumescent flame-retardant and on the UV aging resistance of polypropylene were investigated. By introducing 16 wt% (intumescent flame-retardant /mZnO) and 0.3 wt% maleic anhydride-grafted PP (MAH-g-PP), the limiting oxygen index increased to 32.7 %, and passed UL-94V-0 rating. In comparison to the controls, the peak heat release rate and the peak smoke release rate were 88.5 % and 80 % lower, respectively. In addition, PP samples showed improved mechanical properties, with a 5 % increase in tensile properties compared to the pure PP sample. After 100 h of UV irradiation, the surface of the samples was relatively flat and smooth, and the carbonyl index decreased from 81.1 of neat PP to 26.7. PP composites with 100 h aging treatment still had excellent flame retardancy and mechanical properties. The results showed that mZnO was effective in improving the flame retardancy, mechanical properties and light aging tolerance of PP. This study provides a novel approach to fabricate long-life flame-retardant PP composites with low additive content.

A universal eco-friendly flame retardant strategy for polylactic acid fabrics and other polymer substrates.

Various polymer substrates have their particular combustion features, therefore, developing an effective universal flame retardant strategy for various polymer substrates is of great practical importance. Meanwhile, as substitutes for petroleum-based products, bio-based flame retardants and biodegradable polylactic acid (PLA) meet the requirements of sustainable development. In this work, a fully bio-based flame retardant coating (PAGS) was prepared using phytic acid (PA) and guanosine (GS). PAGS was used as a universal flame retardant coatings for polylactic acid (PLA) fabrics and other substrates, including cotton fabrics, polyethylene terephthalate (PET) fabrics, polyamide (PA) fabrics, polyurethane (PU) foams, polyethylene terephthalate (PET) films, and woods. The PAGS-treated substrates were able to self-extinguish and eliminate molten droplets. Similarly, the PAGS coating significantly suppressed the heat release of each substrate. The P-containing free radicals in the gas phase were able to interact with highly reactive H, HO and alkyl radicals, blocking the chain reaction during combustion. The flammable gas density was also diluted by nonflammable gases. The formed continuous porous and dense intumescent char layer hindered heat and oxygen. It is suggested that this work provides a simple and efficient flame retardant strategy for improving the fire safety of various polymer substrates.

Antisolvent-Free Heterogenous Nucleation Enabled by Employing 4-Tert-Butyl Pyridine Additive and Two-Step Annealing for Efficient CsPbI2 Br Perovskite Solar Cells.

All inorganic perovskite based on CsPbI2 Br has attracted significant attention due to its relatively thermal stable structure compare to its hybrid counterparts. With a wide bandgap of 1.9 eV and excellent light absorption capability, it has been extensively explored for applications in indoor photovoltaics and as a front absorber in tandem devices. However, the uncontrollable crystallization process during solvent evaporation and thermal annealing leads to both macroscopic defects like cracks and microscopic defects such as voids. In this study, a metastable adduct with lead (II) halides by incorporating 4-tert-butyl pyridine as a volatile Lewis base monodentate ligand in the precursor solution is formed. The strategic preferential decomposition of the adduct during the early-stage low-temperature annealing facilitated the desorption of lead (II) halides, inducing antisolvent-free heterogenous nucleation. This, in turn, promoted crystal growth during subsequent high-temperature annealing, resulting in dense films with low defect density. As a result, a maximum open-circuit voltage of 1.30 V is achieved with the champion power conversion efficiency of 16.5% in CsPbI2 Br-based perovskite solar cell. The work reveals a new mechanism of using Lewis acid-base adduct to obtain high quality perovskite films other than hindering crystallization in traditional way.

Imaging Findings and Misdiagnosis of Bronchogenic Cysts: A Study of 83 Cases.

Objective: We characterize computed tomography (CT) and magnetic resonance imaging (MRI) features of bronchogenic cysts (BCs) and analyze misdiagnosis. Methods: The retrospective study consisted of 83 patients with BCs. CT and MRI images were assessed for mass location, maximum diameter, density, calcification, signal intensity, and enhancement pattern. Eighty-three patients underwent plain CT in which 53 underwent enhanced CT. Thirteen patients received both plain and enhanced MR, and only one received just a plain MR. Results: Eighty-three masses were all solitary, with 71 having a roundish morphology, and twelve having a lobulated or irregular morphology. Sixty-six masses are mediastinal type, four are intrapulmonary type, and 13 are ectopic type. Calcification occurred in 14 lesions. On plain CT, 13 lesions displayed water-like attenuation (-20-20 Hu), and 70 showed soft-tissue attenuation (≥21 Hu). On T1WI, eight masses were hyperintense, three were isointense, and three were hypointense. Fourteen masses were hyperintense on T2WI and (Apparent Diffusion Coefficient) ADC sequence. On (Diffusion Weighted Imaging) DWI, six masses were hypointense and eight were hyperintense. Enhanced T1WI showed seven cases were unenhanced, while six were marginally enhanced. Twenty cases were misdiagnosed as thymomas, eleven as neurogenic tumors, six as lymphangiomas, and two as lung cancer. Five cases were misdiagnosed as other diseases. Patients with BCs underwent MR (42.9%) had a lower rate of misdiagnosis than those who underwent CT alone (53.0%). Conclusion: The imaging findings of BCs in the chest are generally consistent. Misdiagnosis occurs frequently when CT attenuation values exceed 20 Hu. Diagnostic accuracy of BCs tends to improve with preoperative MR examination.

Study on the Flame Retardancy of Rigid Polyurethane Foam with Phytic Acid-Functionalized Graphene Oxide.

A rigid polyurethane foam (RPUF) composite was prepared by compounding phytic acid (PA)-functionalized Graphite oxide (PA-GO) with flame-retardant poly (Ammonium phosphate) (APP) and expandable graphite (EG). The effects of PA-GO on the thermal, flame-retardant, and mechanical properties of RPUF were studied using a thermogravimetric analyzer, a limiting oxygen index (LOI) tester, a UL-94 vertical combustion tester, a cone calorimeter, scanning electron microscopy, and a universal tensile testing machine. The results indicated that there was a significant synergistic flame-retardant effect between PA-GO and the intumescent flame retardants (IFR) in the RPUF matrix. Compared with RPUF-1, the addition of 0.3 wt% PA-GO could increase LOI from 25.7% to 26.5%, increase UL-94 rating from V-2 to V-0, and reduce the peak heat release rate (PHRR) and total heat release rate (THR) by 28.5% and 22.2%, respectively. Moreover, the amount of residual char increased from 22.2 wt% to 24.6 wt%, and the char layer was continuous and dense, with almost no holes. Meanwhile, the loss of mechanical properties was apparently lightened.

Differential diagnostic value of tumor markers and contrast-enhanced computed tomography in gastric hepatoid adenocarcinoma and gastric adenocarcinoma.

Objective: This study aimed to investigate the effectiveness of tumor markers and contrast-enhanced computed tomography (CE-CT) in differentiating gastric hepatoid adenocarcinoma (GHA) from gastric adenocarcinoma (GA). Methods: This retrospective study included 160 patients (44 with GHA vs. 116 with GA) who underwent preoperative CE-CT. Preoperative serum concentrations of tumor biomarkers and CT imaging features were analyzed, including alpha-fetoprotein (AFP), carcinoembryonic antigen (CEA), carbohydrate antigen 19-9 (CA19-9), carbohydrate antigen 125 (CA125), tumor location, growth pattern, size, enhancement pattern, cystic changes, and mass contrast enhancement. Multivariate logistic regression analyses were performed to evaluate useful tumor markers and CT imaging features for differentiating GHA from GA. Results: When compared to GA, GHA showed a higher serum AFP [13.27 ng/ml (5.2-340.1) vs. 2.7 ng/ml (2.2-3.98), P <0.001] and CEA levels [4.07 ng/ml (2.73-12.53) vs. 2.42 ng/ml (1.38-4.31), P <0.001]. CT imaging showed GHA with a higher frequency of tumor location in the gastric antrum (P <0.001). GHA had significantly lower attenuation values at the portal venous phase [PCA, (82.34 HU ± 8.46 vs. 91.02 HU ± 10.62, P <0.001)] and delayed phase [DCA, (72.89 HU ± 8.83 vs. 78.27 HU ± 9.51, P <0.001)] when compared with GA. Multivariate logistic regression analyses revealed that tumor location, PCA, and serum AFP level were independent predictors of differentiation between GHA and GA. The combination of these three predictors performed well in discriminating GHA from GA, with an AUC of 0.903, a sensitivity of 86.36%, and a specificity of 81.90%. Conclusions: Integrated evaluation of tumor markers and CT features, including tumor location, PCA, and serum AFP, allowed for more accurate differentiation of GHA from GA.

Constructing lignin based nanoparticles towards flame retardant thermoplastic polyurethane composites with improved mechanical and oxidation resistant properties.

A multifunctional lignin derivative nanoparticle (C-P-Lignin) was synthesized by grafting phenyl dichloro sphosphineoxid and 1, 4-dimethoxyacetylene stepwise on the lignin, then it was applied to prepare the thermoplastic polyurethane (TPU) composite with improved mechanical properties, oxidation resistance, and flame retardancy. The tensile strength, the elongation at break, and the toughness of the TPU/2C-P-Lignin sample reached 28.3 MPa, 941 %, and 139.0 MJ/m2 respectively, which were increased by 39.0 %, 3.4 %, and 33.9 % respectively compared with that of the control TPU sample. The anti-fatigue property was also improved. More importantly, the mechanism of the improved mechanical properties was also calculated and simulated by FTIR and Materials Studio software. The TPU/2C-P-Lignin sample exhibited superior oxidation resistance during the process of photoaging and thermal oxidative aging. Furthermore, the peak heat release rate and the smoke production rate for theTPU/2C-P-Lignin sample was reduced by 50.0 % and 53.8 % compared with that of the control TPU. The reason was that the C-P-Lignin is conducive to the formation of uniformly distributed carbon layers. It is expected that this work can provide a new method for expanding the utilization of waste wood as a multifunctional lignin-based filler to improve fire safety and extend the service life of TPU polymers.

A colloidal gold test strip based on catalytic hairpin assembly for the clinical detection of influenza a virus nucleic acid.

Influenza A epidemics, which occur annually in varying degrees worldwide, is a global challenge to healthcare facilities owing to several limitations of the current detection methods. Therefore, the development of a rapid, convenient, and economical method for the early diagnosis of influenza A will aid clinical treatment and epidemic control. Currently, most of the commonly used clinical rapid tests utilize colloidal gold test strips that detect specific influenza virus antigens but are limited by low sensitivity. Therefore, this study combined catalytic hairpin assembly (CHA) with colloidal gold immunochromatographic assay (GICA) to develop a highly sensitive and visual CHA-GICA test strip. Clinical sample analysis revealed that the sensitivity of the assay was 81.8% and 74% under optimal (35 °C) and room temperature (25 °C) conditions, respectively. In conclusion, this study developed a rapid nucleic acid assay for detecting influenza A virus with high sensitivity and specificity, which can improve the clinical detection of influenza A.

A first-principles study of the structural, electronic and elastic properties of the FeO2-FeO2He system under high pressure.

The origin of the wave velocity anomalies at the core-mantle boundary (CMB) has been controversial. The primordial helium reservoir in the deep lower mantle remains elusive even with geochemical evidence for its existence. Here, we calculated the density and wave velocity of the FeO2-FeO2He system under the CMB conditions using first principles. The FeO2 and FeO2He of pyrite-type can exist stably under the CMB conditions without melting, and the incorporated helium increases the stability of the system. The electrical properties of FeO2 and FeO2He are not related to pressure. Doped helium reduces the density of the system but increases the elastic modulus. Our results suggest that FeO2 can be used as a viable material composition of ultra-low velocity zones (ULVZs), and FeO2He can explain the D'' seismic discontinuity instead of ULVZs. The primordial helium reservoir possibly formed by the accumulation of FeO2He, the only stable solid helium-bearing compound under the CMB conditions, may coincide with the location of the D'' layer.

Improving the hygroscopicity and flame retardancy of polyamide 6 fabrics by surface coating with ß-FeOOH and sulfamic acid.

The combustion of polyamide 6 (PA6) fabrics releases toxic smoke, which will pollute the environment and threaten human life and health. Herein, a novel eco-friendly flame-retardant coating was constructed and applied to PA6 fabrics. Needle-like ß-FeOOH with a high surface area was firstly constructed onto the surface of PA6 fabrics by the hydrolysis of Fe3+, sulfamic acid (SA) was then introduced by a facile dipping and nipping method. The growth of ß-FeOOH also endowed the PA6 fabrics with certain hydrophilicity and moisture permeability, resulting in improved comfortability. The limiting oxygen index (LOI) of the prepared PA6/Fe/6SA sample was increased to 27.2% from 18.5% of control PA6 sample, and the damaged length was reduced to only 6.0 cm from 12.0 cm of control PA6 sample. Meanwhile, the melt dripping was also eliminated. The heat release rate and total heat release values of the PA6/Fe/6SA sample were decreased to 318.5 kW/m2 and 17.0 MJ/m2, respectively, compared with those of control PA6 (494.7 kW/m2 and 21.4 MJ/m2). The analysis results indicated that nonflammable gases diluted flammable gases. The observation of char residues demonstrated that the stable char layer was formed, which effectively inhibited the transfer of heat and oxygen. The organic solvent-free coating does not contain any conventional halogens/phosphorus elements, which provides a useful methodology to produce environmentally friendly flame-retardant fabrics.

Phenanthroline-carbolong interface suppress chemical interactions with active layer enabling long-time stable organic solar cells.

To restrain the chemical reaction at cathode interface of organic solar cells, two cathode interfacial materials are synthesized by connecting phenanthroline with carbolong unit. Consequently, the D18:L8-BO based organic solar cell with double-phenanthroline-carbolong achieve the highest efficiency of 18.2%. Double-phenanthroline-carbolong with larger steric hindrance and stronger electron-withdrawing property confirms to suppress the interfacial reaction with norfullerene acceptor, resulting the most stable device. Double-phenanthroline-carbolong based device can sustain 80% of its initial efficiency for 2170 h in dark N2 atmosphere, 96 h under 85 oC and keep 68% initial efficiency after been illuminated for 2200 h, which are significantly better than bathocuproin based devices. Moreover, superb interfacial stability of double-phenanthroline-carbolong cathode interface enables thermal posttreatment of organic sub-cell in perovskite/organic tandem solar cells and obtained a remarkable efficiency of 21.7% with excellent thermal stability, which indicates the potentially wide application of phenanthroline-carbolong materials for stable and efficient solar device fabrications.

Exploring genetic associations between allergic diseases and indicators of COVID-19 using mendelian randomization.

We carried out a bidirectional Mendelian randomization (MR) including cases of eczema (N = 218,792), asthma (N = 462,933), and allergic rhinitis (N = 112,583). COVID-19 susceptibility (N = 1,683,768), COVID-19 hospitalization (N = 1,887,658), and COVID-19 severe respiratory symptom (N = 1,388,342) were sampled from GWAS database. The MR analysis was primarily based on inverse variance weighted (IVW), supplemented by several other algorithms. In the bidirectional MR analysis, eczema was negatively associated with COVID-19 susceptibility (odds ratio (OR) IVW = 0.92; p = 0.031) and COVID-19 hospitalization (ORIVW = 0.81, p = 0.010); asthma was negatively associated with COVID-19 susceptibility (ORIVW = 0.65, p = 0.005) and COVID-19 severe respiratory symptom (ORIVW = 0.20, p = 0.001). No significant association was found between allergic rhinitis and COVID-19 susceptibility (ORIVW = 0.80, p = 0.174), COVID-19 hospitalization (ORIVW = 0.71, p = 0.207), or COVID-19 severe respiratory symptom (ORIVW = 0.56; p = 0.167). The reverse MR analysis showed no potential reverse causal association. Our findings provided new evidence that allergic diseases might be associated with different risks of COVID-19 susceptibility, hospitalization, and severe respiratory symptom.

Evidence for a causal association between psoriasis and psychiatric disorders using a bidirectional Mendelian randomization analysis in up to 902,341 individuals.

BACKGROUND: The causal association between psoriasis and psychiatric disorders remains ambiguous. OBJECTIVES: This study aimed to investigate the causal relationship between psoriasis and common psychiatric disorders using bidirectional Mendelian randomization (MR) analysis. METHODS: Major depressive disorder (MDD) (N = 217,584), bipolar disorder (N = 51,710), schizophrenia (N = 77,096), and anxiety disorder (N = 218,792) were obtained as outcomes, and psoriasis (N = 337,159) were as exposure. Inverse variance weighting (IVW) was used as the main method, with other sensitivity methods as auxiliary methods. Sensitivity analysis and heterogeneity tests were performed to ensure the robustness of the results. We also performed a subgroup analysis of cases with psoriatic arthritis (PsA) (N = 213,879) by using the same testing methods. RESULTS: MR showed that the genetic risk of psoriasis was positively associated with bipolar disorder (odds ratio (OR) = 13.54, 95 % confidence interval (95%CI): 2.43-75.37, P = 0.002) and MDD (OR = 1.08, 95%CI: 1.01-1.15, P = 0.027), which indicated possible causal relationships between psoriasis and these two diseases. Schizophrenia (OR = 3.52, 95%CI: 0.22-55.71, P = 0.372) and anxiety disorders (OR = 0.65, 95%CI: 0.16-2.63, P = 0.546) indicated no significant causal association. No reverse causal effects of psychiatric disorders on psoriasis were found. Subgroup analysis also suggested causal association of PsA with the bipolar affective disorder (OR = 1.05, 95%CI: 1.01-1.08, P = 0.005). LIMITATIONS: Potential pleiotropic effects, restriction to European populations, and differences in diagnostic criteria. CONCLUSIONS: This study has supported the causal association of psoriasis with MDD and bipolar disorder, and the subtype PsA with bipolar disorder, which informed the intervention for mental illnesses in patients with psoriasis.

A randomized, double-blind, placebo-controlled phase II study to evaluate the efficacy and safety of ivarmacitinib (SHR0302) in adult patients with moderate-to-severe alopecia areata.

BACKGROUND: Alopecia areata (AA) is a CD8+ T cell-mediated autoimmune disease characterized by nonscarring hair loss. Ivarmacitinib, which is a selective oral Janus kinase 1 inhibitor, may interrupt certain cytokine signaling implicated in the pathogenesis of AA. OBJECTIVE: To evaluate the efficacy and safety of ivarmacitinib in adult patients with AA who have ≥25% scalp hair loss. METHODS: Eligible patients were randomized 1:1:1:1 to receive ivarmacitinib 2, 4, or 8 mg once daily or placebo for 24 weeks. The primary end point was the percentage change from baseline in the Severity of Alopecia Tool score at week 24. RESULTS: A total of 94 patients were randomized. At week 24, the least squares mean difference in the percentage change from baseline in the Severity of Alopecia Tool score for ivarmacitinib 2, 4, and 8 mg and placebo groups were -30.51% (90% CI, -45.25, -15.76), -56.11% (90% CI, -70.28, -41.95), -51.01% (90% CI, -65.20, -36.82), and -19.87% (90% CI, -33.99, -5.75), respectively. Two serious adverse events-follicular lymphoma and COVID-19 pneumonia-were reported. LIMITATIONS: A small sample size limits the generalizability of the results. CONCLUSION: Treatment with ivarmacitinib 4 and 8 mg doses in patients with moderate and severe AA for 24 weeks was efficacious and generally tolerated.

Brominated flame retardants coated separators for high-safety lithium-sulfur batteries.

Lithium-sulfur batteries (LSBs) have become highly promising next-generation secondary lithium batteries owing to their high theoretical energy density and abundance of sulfur. Nevertheless, the large-scale application of LSBs is still restricted by the shuttle effect of lithium polysulfide (LiPSs) and the potential fire hazard caused by flammable electrolytes. Herein, three electrolyte-insoluble brominated flame retardants (BFRs) are selected and coated on both sides of commercial polypropylene separators by a facile slurry coating method. The effects of the three BFRs on the safety and electrochemical properties of LSBs are characterized and compared. The coating modification separators greatly improves the flame retardancy of LSBs through radical elimination mechanism. The self-extinguishing time of the electrolyte is reduced from 0.66 s/mg to 0.20 s/mg. Moreover, it is demonstrated that the oxygen (O)-containing BFRs exert a significant adsorption capacity and are more advantageous than O-free BFRs in LSBs. In addition, octabromoether (BDDP) coated separator is more effective in trapping LiPSs than decabromodiphenyl ether (DBDPO) due to higher O content, which can mitigate the shuttle effect and enhance the cycle and rate performance of LSBs. This simple coating strategy for separators with BFRs offers a strongly competitive option for the large-scale production of high-safety LSBs.